Advance-adapters 50-2905 Manual de usuario descargar pdf

ADVANCE ADAPTERS INC. P/N: 50-2905

P.O. Box 247, 4320 Aerotech Center Way New Item: (3/04)

Paso Robles, CA 93447 PAGE 1 OF 4

Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 09-30-08

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will

void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend

that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a

service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive

dealerships and parts stores.

KIT CONSISTS OF:

No. Qty Part No. Description

1. 1 51-2902 C-4 ADAPTER PLATE

2. 1 51-9210 MODIFIED 51-9200 ADAPTER

3. 1 52-2905 C-4 OUTPUT SHAFT- 27 SPLINE

4. 1 KIT 716055 CROSSMEMBER KIT

5. 1 716061 C4 VENT

6. 4 723147 5/16"-18 x 1" F.H.C.S.

7. 5 723701 3/8"-16 NUT

8. 6 723705 3/8"-24 NUT

9. 5 723714 3/8"-16 x 1.5" STUD

10. 6 723731 3/8"-16 x 1" S.H.C.S.

11. 11 911003 3/8" INTERNAL STAR WASHER

GENERAL INFORMATION:

The output shaft included in this kit must be installed into a custom built, fully manual C-4 transmission. The length

of this kit does not leave any space for the governor assembly; therefore, it must be used with a manual valve body.

Additionally, the governor housing needs a lathe modification and a mill/drill press modification.

INSTRUCTIONS:

1. Have a transmission shop build the fully manual C-4 with the 52-2905 output shaft.

2. Give the governor casting to a qualified machinist to turn the part down to the desired thickness of 0.530" +/- 0.005".

This can be seen below in the picture. The second modification is to countersink the four 5/16" bolt holes until the

included 5/16"-18 flat head cap screws sit flush with the surface.

GOVERNOR HOUSING:

To the left is the unmodi-

fied housing. To the right

is the housing after it has

been machined down to

the correct thickness of

0.530" +/- 0.005".

FORD C-4 300M TO ATLAS

TRANSFER CASE- SHORT

Kit Note:

The adapter overall

length is 2.9" long.

1 2 3 4

Indice de contenidos

Pagina 1 - TRANSFER CASE- SHORT

ADVANCE ADAPTERS INC. P/N: 50-2905P.O. Box 247, 4320 Aerotech Center Way New Item: (3/04)Paso Robles, CA 93447 PAGE 1 OF 4Telephone: (800) 350-2223

Pagina 2 - FORD C-4 TO ATLAS

3. The dowel pin must be shortened to 1.40" so that it is flush with the shortened governor housing.4. Place the governor housing over the park g

Pagina 3

7. Apply a thin film of silicone to the backflange of the C4 transmission and using amallet, tap the 51-2902 steel plate over thegovernor housing. Fas

Pagina 4

The assembled kitlooking from the top.The assembled kit lookingfrom the bottom.FORD C-4 300M TO ATLASTRANSFER CASE- SHORTADVANCE ADAPTERS INC. P/N: 5

Comentarios a estos manuales

Sin comentarios

Advance-adapters 50-2905 Manual de usuario

Busca en linea o descarga Manual de usuario para Para El Coche Advance-adapters 50-2905. Advance Adapters 50-2905 User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Para El Coche Advance-adapters 50-2905